超音速气流中热塑性复合材料壁板的非线性热颤振特性

热塑性复合材料结构在高速流场中的颤振行为是可重复使用航天器设计中需要考虑的问题.基于Mindlin厚板理论和Von-Karman大变形理论描述热塑性复合壁板结构大变形,超音速气动力采用活塞气动理论.考虑温度引起的壁板面内热应力和热塑性材料力学性能的改变.根据虚功原理和有限元法推导建立了热塑性复合材料壁板的热颤振模型,进...     

燃烧室压力对潜入式喷管喉衬热应力的影响

为了研究燃烧室压力对固体火箭发动机潜入式喷管热应力影响规律的问题,采用商业流体软件,基于压力求解器,求解了喷管纯气相的流场,确定了燃气温度、压力、壁面对流换热系数;采用有限元软件,依据流场计算的非均布壁面压力与非均布对流换热,求解了燃烧室压力为6 MPa下的潜入式喷管热结构问题;通过地面点火试验验证了仿真模型与数值方法的有效性与准确性;采用相同计算模型与数值方法,求解了在燃烧室压力为9 MPa、12 MPa下的喷管热结构问题,揭示了燃烧室压力对喉衬热应力的影响规律。结果表明:整个工作过程,喉衬环向应力最大值为103.9 MPa,位于内表面,且随时间增大,先增大后减小;喉衬环向拉应力也随时间先增大后减小;随压力增大,对流换热系数增大,喉衬温度升高,喉衬环向拉应力增大,喉衬环向压应力减小。     

Experimental and numerical study of the blast wave decrease using sandwich panel by granular materials core

Among the intrinsic properties of some materials, e.g., foams, porous materials, and granular materials, are their ability to mitigate shock waves. This paper investigated shock wave mitigation by a sandwich panel with a granular core. Numerical simulations and experimental tests were performed using Autodyn hydro-code software and a shock tube, respectively. The smoothed particle hydrodynamics (SPH) method was used to model granular materials. Sawdust and pumice, whose properties were determined by several compression tests, were used as granular materials in the sandwich panel core. These granular materials possess many mechanisms, including compacting (e.g., sawdust) and crushing (e.g., pumice) that mitigate shock/blast wave. The results indicated the ineffectiveness of using a core with low thickness, yet it was demonstrated to be effective with high thickness. Low-thickness pumice yielded better results for wave mitigation. The use of these materials with a core with appropriate core reduces up to 88% of the shock wave. The results of the experiments and numerical simulations were compared, suggesting a good agreement between the two. This indicates the accuracy of simulation and the ability of the SPH method to modeling granular material under shock loading. The effects of grain size and the coefficient of friction between grains have also been investigated using simulation, implying that increasing the grain size and coefficient of friction between grains both reduce overpressure.     

Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

大地靶场地面散射特性的测试方法

通过对大地靶场地面电磁环境特性的分析,依照大地靶场对武器系统工作状态的影响,提出了大地靶场地面散射特性的测试原理。同时对测量方法、测量系统等,也作了具体的分析论证,这对武器系统的研制、生产、试验等环节及地杂波特性的研究具有重要的意义。     

发动机缸内压缩压力非接触式检测方法研究

发动机汽缸压缩压力是检测发动机机密封性的重要参数.发动机密封性降低,会造成发动机经济性、动力性下降及废气排放指标恶化,因此对各缸压缩压力的检测具有重要意义.现提出一种利用曲轴瞬时转速,进行不解体检测坦克发动机汽缸压缩压力的方法.通过实车测量获得缸压及转速的特征参数,利用灰色理论模型的方法建立了发动机转速脉动与汽缸压缩压力的数学关系.试验结果表明,利用这种方法进行缸内压缩压力测量是可行的.     

一种新型防护结构对爆炸冲击波衰减特性的研究

运用大型有限元软件LS—DYNA,在相同爆炸冲击波作用下,对洞库口部普通钢板防护门和有泡沫铝夹层的钢板防护门两种防护结构的隔爆性能进行了数值模拟和对比分析,结果表明:有泡沫铝夹层的钢板防护门对爆炸冲击波有着良好的衰减特性。同时表明该新型防护结构对洞库口部抗爆炸冲击波设计有着很高的参考价值。     

高透波性大刚度桅杆设计与性能测试分析

提出了用复合材料技术设计与制造高透波性大刚度桅杆的方法,以高强玻璃纤维为增强材料、SW905乙烯基脂树脂为基体材料,制作出1∶1桅杆模型,对制作出的桅杆模型进行了性能测试.测试结果表明,制作出的桅杆具有高透波性和较大的动刚度.     

合成孔径声纳的数学问题

根据波动方程线性化模型,考虑了合成孔径成像的数学问题,对于在二维曲面上所获得的数据来重建三维景物,将基阵的运动和旋转归结为对基阵轨迹的依赖上.利用微局部分析给出了一般问题的一种新的理论反演算法,并且分析了成像系统的分辨率,从而为今后的工作打下理论基础.     

REBO模型的平衡态分子动力学模拟

为了得到合适的"计算机实验"的"试样"进行固体炸药冲击起爆现象的分子动力学研究,对REBO模型进行了NVE,NVT两种平衡态分子动力学模拟;作为对比,同时还进行了不施加任何人工干预,系统的演化完全由运动方程驱动的分子动力学模拟,讨论了根据对"试样"的不同要求选择适当模拟方法的原则。